Bond Strength Tester, 220V 50/60Hz Manufacturer,Supplier and Exporter in India

Product Code : EL-CAMT-11055
Lab Equipment India is a leading Bond Strength Tester, 220V 50/60Hz Manufacturer,and suppliers in India, Bond Strength Tester, 220V 50/60Hz Manufacturer,and suppliers in South Africa, Bond Strength Tester, 220V 50/60Hz Algeria (Algiers), Bond Strength Tester, 220V 50/60Hz Angola (Luanda), Bond Strength Tester, 220V 50/60Hz Argentina (Buenos Aires), Bond Strength Tester, 220V 50/60Hz Armenia (Yerevan), Bond Strength Tester, 220V 50/60Hz Australia (Canberra), Bond Strength Tester, 220V 50/60Hz Austria (Vienna), Bahrain (Manama), Bangladesh (Dhaka), Bhutan (Thimphu), Bolivia (Sucre), Botswana (Gaborone), Brazil (Brasília), Brunei (Bandar Seri Begawan), Montenegro (Podgorica), Morocco (Rabat), Mozambique (Maputo), Myanmar (Naypyidaw), Namibia (Windhoek), Nepal (Kathmandu), New Zealand (Wellington), Nigeria (Abuja), Oman (Muscat), Palestine (Ramallah), Panama (Panama City), Papua New Guinea (Port Moresby), Paraguay (Asunción), Peru (Lima), Philippines (Manila)¸ Portugal (Lisbon), Qatar (Doha), Rwanda (Kigali), Saudi Arabia (Riyadh), Senegal (Dakar), Serbia (Belgrade), Sierra Leone (Freetown), Slovakia (Bratislava), South Africa (Cape Town) (Pretoria) (Bloemfontein), South Sudan (Juba), Spain (Madrid), Sri Lanka (Sri Jayawardenepura Kotte) (Colombo), Sudan (Khartoum), Syria (Damascus), Tanzania (Dodoma), Thailand (Bangkok), Togo (Lomé), Tonga (Nuku'alofa), Trinidad and Tobago (Port of Spain), Tunisia (Tunis), Turkey (Ankara), Turkmenistan (Ashgabat), Uganda (Kampala), United Arab Emirates (Abu Dhabi), United Kingdom (London), United States (Washington, D.C.).

Product Description

Bond Strength Tester, 220V 50/60Hz

The Multiple bond strength tester is a computer-controlled hydraulically operated device with which several samples can be tested in a short sequence (approx. 20-25 pieces depending on the arrangement). 

The manual positioning of the pulling device is carried out on low-friction linear slides. 

Computer-aided multiple bond strength tester with force- or displacement-controlled test execution and deformation measurement.

Thus the tests can be carried out very comfortably and quickly. 
The bond strength is determined using a highly sensitive force transducer of class 0.2. 

A displacement measuring system is installed in the cylinder with which the deformation of the coating of the test specimen under load can be determined. The tests can be carried out both force- and displacement-controlled. 

This makes the instrument suitable both for large laboratories with high testing volumes and for research facilities. 

The entire instrument is mounted on a stainless steel substructure in which the hydraulic and electrical components are installed. 
All tests are recorded with software and can be subsequently analyzed and transferred to a freely configurable protocol. 
The graphical display of the measured value curve allows samples to be compared with each other at a glance.
 
The hydraulic system is driven by a powerful radial piston pump. 

The electrical system is switched via a main switch with under-voltage release and the test can be interrupted immediately via an emergency stop button.

Both round and square samples of different sizes can be tested (e.g. diameter 50 mm or 50 x 50 mm). 

The samples are attached to a support plate (e.g. concrete) with the dimensions 400 x 400 mm and then inserted into the device via a heavy-duty pull-out and clamped there. 

The replacement of the slabs takes less than one minute. 

Plates with thicknesses from 10 to 80 mm can be used for fixing the specimens. 
 
The device covers all international standards and can also be configured for completely free test runs. 

This means that the device can also be used in the long term in case of any changes to standards. 

Standard configuration is 20kN, other load configurations are available, please enquire.

Supports the following standards : ASTM C1583, ASTM D4541, ASTM D7234, ASTM D7522; BS 1881 Part 207, EN 12004-2, EN 12002, EN 1324, EN 1542, EN 1015, EN 1348, EN 13892-8; DIN 1048-2, DIN 13279-2, ISO 4624


   

Follow Us